electricians
Chicago Bungalow Rewiring Cost in Illinois: Real Price Ranges and Why Conduit Changes the Math
A full rewire of a Chicago bungalow often runs $18,000 to $40,000 because the city requires metal conduit. See price ranges by scope and how the suburbs compare.
In This Article
Chicago Bungalow Rewiring Cost in Illinois: Real Price Ranges and Why Conduit Changes the Math
Most full rewires of a classic Chicago bungalow land somewhere between $18,000 and $40,000, and plenty of owners are surprised the number is that high for a 1,200 square foot brick house. The reason is mostly the city's electrical code. Chicago generally requires wiring to run in metal conduit, usually EMT, instead of the plastic-sheathed cable used almost everywhere else in the country.
That one rule shapes the whole job: how long it takes, how many walls get opened, and which contractors can bid it. Below is a breakdown of what drives the price on a typical bungalow in Portage Park, Jefferson Park, Chatham, Brighton Park, or West Lawn, plus how the suburbs compare.
What Bungalow Owners Pay, by Scope
Price depends on how much of the house you are replacing and how finished the basement and attic are. These are approximate ranges for work inside Chicago city limits by a licensed electrical contractor, including the permit.
| Scope of work | Approximate cost |
|---|---|
| Kitchen only, new circuits in conduit | $4,500 to $9,000 |
| Main floor rewire, basement left open | $10,000 to $18,000 |
| Full rewire, unfinished attic and basement | $18,000 to $28,000 |
| Full rewire with finished attic bedrooms | $25,000 to $40,000 |
| New 200-amp service and panel | $3,500 to $6,500 |
Plaster repair, painting, and any work by ComEd on the service drop are usually separate. If the bungalow still has a fuse box or a 60-amp service, plan on the service upgrade as part of any full rewire, because a modern kitchen and central AC will not fit on the old one.
These numbers run well above what an owner in Peoria or Rockford would pay for a similar house. Most of the gap comes from conduit labor, plus the higher wage rates of union and city-licensed shops.
Why Chicago Wiring Costs More: The Conduit Rule
Outside Chicago, an electrician rewiring an old house usually fishes nonmetallic cable through the walls. It bends around corners, slides through small holes, and goes in fast. Chicago's electrical code has long required metal raceway in most buildings, which means bending and joining sections of EMT or using flexible metal conduit where rigid pipe will not fit.
Conduit takes more time to install, especially inside finished plaster walls. Rigid pipe cannot snake through a wall the way cable can, so the electrician often uses flexible metal conduit for the hidden runs and EMT in the basement and attic where it can be strapped to joists. Each box, bend, and connector adds minutes, and a house has hundreds of them.
There is an upside. Conduit protects the wire from nails, rodents, and damage, and the metal pipe serves as a grounding path. It also makes later changes easier, since new wire can sometimes be pulled through existing conduit without opening a wall again.
What Conduit Means for Your Walls
Expect more access holes than a cable job would need. Electricians typically cut openings at the top of each wall near the ceiling, at outlet locations, and in closets to route flex conduit through plaster and lath.
A good contractor will plan routes that use closets, the basement ceiling, and the attic floor to keep holes in the main rooms to a minimum. Ask to see that plan before signing, and ask who patches the plaster.
How a Bungalow's Layout Affects the Job
The classic Chicago bungalow went up between roughly 1910 and 1940: one and a half stories, brick on all sides, a full basement, and an attic that many families later finished into bedrooms. That layout is both good and bad for an electrician.
The good part is the open basement. Most bungalows still have exposed joists below the main floor, which gives the crew an easy path to reach every first-floor outlet from below. The attic, if unfinished, does the same for the main floor ceilings and the second-story outlets.
The hard part is the exterior walls. Bungalow brick walls usually have plaster applied over furring strips or straight to the masonry, which leaves little or no cavity for wire. Electricians tend to route outlets on exterior walls from the floor below or through the baseboard instead of trying to fish up the wall.
Finished Attics and Dormers
A finished attic with knee walls and sloped ceilings is where many bungalow rewires get expensive. Space behind the knee walls is often tight, and the slope leaves little room above the ceiling. If the attic was finished decades ago, it may also have its own patchwork of old circuits fed from somewhere unexpected.
Owners planning to redo the attic anyway should time the rewire with that project. Running conduit through open framing costs far less than doing it behind finished drywall.
Basements and Garden Units
Many bungalows in Belmont Cragin, Gage Park, and Berwyn have a finished basement, sometimes with a second kitchen. Those spaces need their own circuits, GFCI protection, and often a dedicated circuit for a sump or ejector pump. If the basement is finished, figure on extra labor to open the ceiling or run surface conduit.
What Electricians Find Behind Bungalow Plaster
Very few bungalows still run on a single original system. A typical house in North Park or Auburn Gresham has knob-and-tube in a few ceiling circuits, armored BX cable from a 1950s update, and a scattering of newer conduit runs added when someone remodeled the kitchen or finished the basement. The electrician has to trace all of it before quoting a final number.
Old BX deserves a mention. Early armored cable often lacks a separate ground wire, and the metal jacket itself was relied on as the ground path. After 80 or 90 years of corrosion and loose fittings, that path may not be reliable, so most electricians treat early BX as due for replacement along with any knob-and-tube.
Expect some surprises in the panel area too. Many bungalows have a fuse box that was later fed into a small breaker panel, or a subpanel tacked on for a basement unit, and the grounding at the water pipe may be missing a bond around the meter. These are fixable, but they belong in the quote from the start.
A pre-bid walkthrough, where the electrician opens a few outlet boxes and looks at the basement ceiling, usually takes an hour. Contractors who skip that step and quote over the phone are guessing.
Chicago Versus the Suburbs
Several older inner-ring suburbs have adopted their own local amendments, and some also lean toward conduit or require it in certain buildings. Others allow standard cable, which can cut the cost of a comparable rewire by a quarter or more. Berwyn, Cicero, Oak Park, Evanston, and Skokie each set their own rules, so ask each contractor what the local code requires before comparing bids.
Illinois does not issue a single statewide electrician license, so licensing depends on the municipality. Inside Chicago, electrical work has to be performed under a city-licensed supervising electrician working for a registered contractor, and the Chicago Department of Buildings issues the permit. A suburban electrician without city credentials cannot pull a Chicago electrical permit.
A bid from a contractor outside the city that seems far cheaper may be priced for cable, not conduit. Compare line items, not just totals.
Permits, Inspections, and Timeline
A full rewire in Chicago requires an electrical permit and inspections. The Department of Buildings typically checks rough-in work before walls are closed and does a final inspection at the end, and permit timing can add a few weeks to the schedule before work starts.
On the job itself, a full bungalow rewire in conduit usually takes two to four weeks of crew time. Owners often stay in the house, with power shut off to one area at a time. If ComEd needs to reset the service drop or meter for a new 200-amp service, that appointment adds its own lead time.
How to Keep the Bill Reasonable
The biggest savings come from planning the work around other projects. Rewiring before a kitchen remodel, before finishing the attic, or before insulating the attic floor avoids opening the same surfaces twice.
Getting three written bids also helps, as long as they are comparable. Each should list the number of circuits, the outlet and switch count, conduit type, panel size, permit fees, and who handles plaster patching. A low bid that leaves out the service upgrade or patching is not a low bid.
If you want a starting list of local contractors, you can browse licensed electricians in your area and filter by city. Our blog on home repair costs also covers other repair questions Illinois homeowners ask.
Phasing the work is the other option. Some owners rewire the kitchen, baths, and basement first, then tackle bedrooms the next year. That can work on a budget, though it usually costs more in total because of repeat setup and permits.
Bungalow Rewiring Questions
Can I use Romex in my Chicago bungalow if I do it myself?
Generally no. Chicago's code calls for metal raceway in most residential work, and permits for electrical work in the city go to licensed supervising electricians, not homeowners. An unpermitted job also tends to come up during a sale inspection.
Does the Chicago Bungalow Association help with rewiring costs?
The association has offered guidance, contractor resources, and at times grant or loan programs for historic bungalow owners. Programs change from year to year, so check what is available before you start work.
How do I know if my bungalow still has knob-and-tube?
Look at the basement ceiling for single wires on porcelain knobs, and check for two-prong outlets and a fuse box. Many bungalows were partially updated with armored cable in the 1950s, so an electrician's inspection, usually $150 to $350, tells you what is still live.
Is rewiring worth it if I plan to sell in a few years?
Often yes. Buyers' inspectors flag old wiring in nearly every pre-war Chicago house, and lenders and insurers may ask questions, so a completed, permitted rewire removes a big negotiating point.