electricians
Average Electrician Rates Across Illinois: Chicago Prices Versus Downstate
Chicago electricians often charge $110 to $175 an hour, while downstate rates run far lower. Compare Illinois prices, conduit rules, and local licensing.
In This Article
Average Electrician Rates Across Illinois: Chicago Prices Versus Downstate
A licensed electrician in Chicago commonly bills $110 to $175 an hour, while the same work in Peoria or Springfield is closer to $70 to $115. Here is roughly how the state lines up.
| Location | Approximate hourly rate | Service call minimum | 200-amp panel upgrade |
|---|---|---|---|
| Chicago | $110 to $175 | $150 to $300 | $3,500 to $6,500 |
| Naperville and the collar counties | $95 to $150 | $125 to $250 | $2,800 to $5,000 |
| Rockford | $75 to $120 | $100 to $200 | $2,000 to $3,800 |
| Peoria | $70 to $115 | $90 to $175 | $1,800 to $3,500 |
| Springfield | $70 to $110 | $90 to $175 | $1,800 to $3,400 |
Those are ballpark ranges for residential service work, and a specific quote can fall outside them. Three things explain most of the spread: union labor, the way Chicago requires wiring to be installed, and the absence of one license that applies across Illinois.
Illinois does not issue a statewide electrician license, so your protection depends on what your city or county requires. A homeowner in a small downstate town may have far less built-in screening than one in Chicago, which makes the hiring questions matter more.
Why Chicago Costs So Much More
Chicago is one of the strongest union construction markets in the country. IBEW Local 134 covers electrical workers in the city and much of Cook County, and union wage and benefit packages set a high floor for commercial work. Residential shops are not all union, but they compete for the same trained electricians, so the local labor price rises across the board.
Overhead adds another layer. Vans, parking tickets, insurance, and city licensing all cost more here, and contractors build that into every hour. A 30-minute trip can eat most of a service minimum when traffic on the Kennedy is backed up, which is one reason minimum charges in the city run higher.
The buildings raise the price as well. Bungalows, two-flats, and courtyard buildings often have plaster walls, older fuse boxes, and shared basements, and each of those adds time before any new wire goes in. A 60-amp fuse panel in a two-flat might also need separate meters and a service change for each unit, so one upgrade can turn into two.
The Conduit Rule
Chicago has long stood apart from most of the country on residential wiring methods. The Chicago Electrical Code has traditionally called for metal raceway and metal boxes in homes, where much of the US uses plastic-sheathed NM cable, often known by the brand name Romex. Electrical metallic tubing, or EMT, takes longer to bend, fit, and pull through than cable.
On a kitchen remodel, that can add roughly 20% to 40% to the labor compared with the same layout in a town that allows cable. Rewiring a two-flat in Chicago can land around $20,000 to $45,000, depending on size and wall access. Plaster walls and old bungalow framing can push it higher, though conduit also gives you a tougher installation that is easier to modify later.
Several suburbs have similar requirements, and others follow the National Electrical Code more closely. Ask your village building department which wiring method it expects, since this one answer can move a bid by thousands of dollars.
City Licensing
Chicago runs its own licensing system through the Department of Buildings. A business needs a City of Chicago electrical contractor license to install or alter wiring regulated by the city's electrical code, and it must employ a licensed supervising electrician. Ask for the contractor's Chicago license number, because a license from a neighboring suburb is a different credential from the city's own.
The Suburban Middle Ground
Naperville sits in the higher-cost suburban band, with rates usually around $95 to $150 an hour. Many homes there were built in recent decades, so jobs tend to be additions such as EV chargers, finished basements, and hot tub circuits instead of rewires. A Level 2 charger circuit commonly costs around $700 to $1,800 depending on the distance from the panel.
Naperville also runs a municipal electric utility, which affects service upgrades. Any job that needs a new meter or larger service goes through the city's own utility process, while most neighbors in surrounding towns deal with ComEd. Your electrician should be able to tell you who to call and how long that step usually takes.
Across DuPage, Lake, Kane, and Will counties, each town has its own permit fees and inspectors. A permit might cost $75 in one village and $300 in the next, and some require contractors to register locally before pulling one. Getting two or three quotes from shops that regularly work your town can save time here, since they already know the inspector's expectations.
What Downstate Homeowners Pay
Drive about 90 minutes northwest of the Loop and the numbers change. Rockford electricians commonly charge about $75 to $120 an hour, and the city's many older brick and frame homes generate steady demand for panel swaps and knob-and-tube replacement. A whole-house rewire on a modest Rockford home may run about $9,000 to $18,000, which is well under half of a comparable Chicago two-flat job.
Peoria and Springfield are usually lower still. Ameren serves much of central Illinois, while Springfield has City Water, Light and Power, so utility coordination depends on where you live. Peoria's older hillside neighborhoods can add difficulty with long service runs and tight access, but the base rate typically stays near $70 to $115.
Farther south and in rural counties, prices may look even friendlier on paper. Trip charges often make up the difference, because a single electrician may cover several counties. A farm outbuilding service or well pump circuit can include $50 to $150 in travel before work starts.
Fewer electricians also means less competition on bigger jobs. In a town served by only one or two shops, a panel upgrade or barn service may carry a price closer to Peoria's top range, and the wait can stretch past a month during busy stretches. Calling a contractor from the nearest larger city can give you a useful second number, even after you count the drive.
Sample Job Prices in Both Markets
Say you need four new recessed lights in an existing living room ceiling. In Rockford or Peoria, that might cost about $600 to $1,000. In Chicago, where the wiring may have to run in conduit through plaster, a similar job might run closer to $1,200 to $2,200.
Common jobs show a similar pattern. These are rough installed prices, with downstate first and Chicago second:
- Replacing a standard outlet or switch: $100 to $200 downstate, $175 to $350 in Chicago.
- Adding a dedicated 20-amp circuit: $250 to $600 downstate, $500 to $1,200 in Chicago.
- Hardwiring a ceiling fan where a box already exists: $125 to $300 downstate, $225 to $450 in Chicago.
- Installing a whole-house surge protector: $250 to $500 downstate, $400 to $800 in Chicago.
The downstate figure usually assumes cable is allowed, so check your own town's rule. That single assumption explains much of the gap on any job that involves new wiring.
Checking Credentials Without a State License
With no state registry to search, the job of checking credentials falls to you. Start with your city or village hall, and ask whether it licenses or registers electrical contractors and whether a permit is required for your project. Some municipalities have a formal process with exams, while others accept proof of insurance and a registration fee.
Insurance and permits are your best protection in towns with lighter rules. Request a certificate of liability insurance sent directly from the agent, and make sure workers' compensation coverage is in place if the shop has employees. A contractor who pulls a permit also brings an inspector into the job, which gives you a second set of eyes for a modest fee.
Licensing rules in Illinois can change at the local level without much notice, so confirm the current requirement before signing anything. You can also compare licensed electricians across Illinois and read more home repair pricing guides as you build a budget. A detailed quote should name the wiring method, the permit, and who handles any utility work.
Illinois Electrician FAQs
Can a Naperville electrician work in Chicago?
Only if the business holds the licensing Chicago requires, which is separate from any suburban credential. A suburban shop without that license generally has to stay out of city work, even for a small job in Edison Park.
Is non-union labor always cheaper around Chicago?
Often it is, by perhaps $15 to $40 an hour on residential service work, but not every time. Compare the full scope of each bid, since a lower rate with more estimated hours can end up costing the same.
When is the best time to book a big Illinois electrical project?
Late fall and winter can offer more flexible scheduling for interior work, because outdoor and construction jobs slow down across the state. Springfield and Peoria shops may have shorter lead times than Chicago contractors, which can run several weeks out on larger jobs.
Does Illinois offer help with panel upgrade costs?
Rebate availability changes and often depends on your utility or income level, so check with ComEd, Ameren, or your municipal utility before you budget around one. A panel tied to an EV charger or heat pump is the most likely candidate if a program is running.